ISO INTERNATIONAL STANDARD 13315-2 Firstedition 2014-05-01 Environmental management for concrete and concrete structures Part 2: System boundary and inventory data Managementenvironnemental dubeton etdesstructures enbeton- Partie2:Limitedusystemeetdonnéesd'inventaire Reference number ISO 13315-2:2014(E) ISO @IS0 2014 IS013315-2:2014(E) COPYRIGHTPROTECTEDDOCUMENT @IS02014 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either Iso at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56: CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax +41 22 74909 47 E-mail [email protected] Web www.iso.org Published in Switzerland ii @IS02014-Allrights reserved IS0 13315-2:2014(E) Contents Page Foreword .iv Introduction .V 1 Scope 1 2 Normativereferences 1 3 Terms and definitions 1 4 System boundary. 2 4.1 General 2 4.2 Constituents. 2 4.3 Reinforcing and prestressing steel 7 4.4 Formwork,falsework,and machinery 8 4.5 Concrete. 9 4.6 Precast concrete. 10 4.7 Execution of concrete structures. 11 4.8 Use of concrete structures 13 4.9 End phase of concrete and concrete structures 14 5 Inventory data 17 5.1 General 17 5.2 Constituents 18 5.3 Reinforcingand prestressing steel 21 5.4 Formwork,falsework,andmachinery 22 5.5 Production of concrete. 23 5.6 Executionofconcretestructures 24 5.7 Use of concrete structures. 25 5.8 Endphase of concrete and concretestructures 26 6 Critical review and its storage. 27 Bibliography 28 IS0 2014-All rights reserved ii IS013315-2:2014(E) Foreword Iso (the International Organization for Standardization) is a worldwidefederation of national standards bodies (Iso member bodies).The work of preparing International Standards is normally carried out throughIsotechnicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with Iso, also take part in the work. ISOcollaboratescloselywiththeInternationalElectrotechnicalCommission(IEC)onallmattersof electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISo/IE Directives, Part 1. In particular the different approval criteria needed for the different types of Iso documents should be noted. This document was drafted in accordance with the editorialrulesoftheISo/IECDirectives,Part2 (seewww.iso.org/directives). Attentionis drawn to thepossibilitythat some ofthe elements of this document maybe the subjectof patent rights. IsO shall not be held responsible for identifying any or all such patent rights. Details of anypatentrights identified during the development of thedocument will be inthe Introduction and/or Any trade name used in this document is information given for the convenience of users and does not constituteanendorsement. For an explanation on the meaning of Iso specific terms and expressions related to conformity assessment, as well as information about IsO's adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsiblefor this documentis Iso/TC 71, Concrete, reinforced concrete and pre-stressed concrete, Subcommittee SC 8, Environmental management for concrete and concrete structures. Is013315 consists ofthefollowing parts,underthegeneraltitle Environmental managementfor concrete and concrete structures: Part 1: General principles Part2:Systemboundaryand inventorydata NOTE The ISo 13315 series provides specifications for concrete and ensures consistency with the existingenvironmentalIS014000series,IS015392,IS021930