ISO INTERNATIONAL STANDARD 1268-6 First edition 2002-04-15 Fibre-reinforced plastics Methods of producing test plates - Part 6: Pultrusion moulding Plastiquesrenforcés defibresMethodesdefabrication deplaques d'essai Partie6:Moulageparpultrusion Reference number ISO 1268-6:2002(E) ISO @ISO 2002 ISO1268-6:2002(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The IsO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters @ISO2002 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Casepostale 56·CH-1211Geneva20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.ch Printed in Switzerland ISO1268-6:2002(E) Foreword ISO (the International Organization for Standardization)is a worldwide federation of national standards bodies (isO member bodies). The work of preparing International Standards is normally carried out through IsO technical liaison with IsO, also take part in the work. Iso collaborates closely with the International Electrotechnical Commission (IEC) on allmatters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEc Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Attention is drawn to the possibility that some of the elements of this part of isO 1268 may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 1268-6 was prepared by Technical Committee ISO/TC 61,Plastics, Subcommittee SC13,Compositesandreinforcementfibres. ISo 1268 consists of the following parts, under the general title Fibre-reinforced plastics - Methods of producing testplates: Part 1:Generalconditions Part2:Contact and spray-up moulding -Part3:Wetcompressionmoulding Part 4: Moulding of prepregs Part5:Filamentwinding Part6:Pultrusionmoulding Part7:Resintransfermoulding Part8:CompressionmouldingofSMCandBMC Part 9:Moulding of GMT/STC Part1o:Injection moulding of BMC and other long-fibre moulding compounds- General principles and mouldingofmultipurposetestspecimens Part 11:Injectionmoulding of BMC and other long-fibremoulding compoundsSmall plates INTERNATIONALSTANDARD ISO1268-6:2002(E) Fibre-reinforced plastics Methods of producing test plates - Part 6: Pultrusion moulding 1 Scope This part of isO 1268 specifies a pultrusion-moulding method for preparing reinforced plastics test plates to be used for the preparation of test specimens to determine the mechanical and physical properties of the laminate. or aramid fibres alone or in combination and in any form suitable forthe pultrusion process (continuous rovings, tows, mats, fabrics or combinations of these). This part of ISO 1268 is intended to be read in conjunction with ISO 1268-1. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of isO1268.Fordated references, subsequent amendmentsto, or revisions of, any of thesepublicationsdo not apply. However, parties to agreements based on this part of isO 1268 are encouraged to invest