ISO INTERNATIONAL STANDARD 1207 Third edition 2011-08-01 Slotted cheese head screws Product grade A Vis a métaux a tete cylindrique fendue-Grade A iTeh STANDARD PREVIEW (standards.iteh.ai) ISO 1207:2011 https:/standards.iteh.ai/catalog/standards/sist/e886976f-303b-4c11-93ff- a47ec5d5437a/is0-1207-2011 Reference number ISO 1207:2011(E) @ISO 2011 ISO 1207:2011(E) iTeh STANDARDPREVIEW (standards.iteh.ai) ISQ 1207:2011 https//standards.iteh.ai/catalog/standards/sist/e886976f-303b-4c11-93f- a47ec5d5437a/is0-1207-2011 COPYRIGHTPROTECTEDDOCUMENT ISO2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, IsO's member body in the country of the requester. ISO copyright office Case postale 56.CH-1211Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ii @ ISO 2011 - All rights reserved ISO1207:2011(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies non-governmental, in liaison with IsO, also take part in the work. IsO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standardsare drafted inaccordancewiththe rulesgiveninthe ISO/lECDirectives,Part2 The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75% of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO1207waspreparedbyTechnical CommitteeISO/TC2,Fasteners,SubcommitteeSC11,Fastenerswith metric externalthread. Ceh revised. (standards.iteh.ai) ISQ 1207:2011 https://standards.iteh.ai/catalog/standards/sist/e886976f-303b-4c11-93f- a47ec5d5437a/is0-1207-2011 IsO 2011-All rights reserved ili iTehSTANDARDPREVIEW (standards.iteh.ai) ISO 1207:2011 https:/standards.iteh.ai/catalog/standards/sist/e886976f-303b-4c11-93ff- a47ec5d5437a/is0-1207-2011 INTERNATIONAL STANDARD ISO 1207:2011(E) Slotted cheese head screws Product grade A Scope This International Standard specifies the characteristics of slotted cheese head screws of product grade A and with threads from M1,6 to M10 inclusive. If, in special cases, specifications other than those listed in this International Standard are required, they can ISO3506-1.ISO4759-1. 2 Normativereferences The following referenced documents are indispensable for the application of this document. For dated document (including any amendmenf)APRliDARD PREVIEW IsO261,/sOgeneralpurposemetric screwthreads_Generalplan ISQ 1207:201 Iso 898-1, Mechanidalpproperties.tfhfaistenerstmdddsofstarbonsteelandlallojffsteel- Part 1: Bolts, screws andstudswithspecifiedpropertyclassesec5Cdarseésthlead-andfinepitchthread Iso 965-2, so general purpose metric screw threads-Tolerances-Part 2: Limits of sizes for general purposeexternaland internal screwthreadsMedium quality Iso 965-3,/sogeneral purpose metric screw threads-Tolerances-Part3:Deviations for constructional screwthreads Iso3269,Fasteners—Acceptanceinspection Iso3506-1,Mechanicalpropertiesofcorrosion-resistantstainlesssteelfastenersPart1:Bolts,screwsand studs IsO4042,Fasteners—Electroplated coatings ISo4753,Fasteners-Endsofpartswithexternal/sOmetricthread IsO4759-1,TolerancesforfastenersPart1:Bolts,screws,studsandnuts—ProductgradesA,BandC Iso 6157-1,Fasteners—Surface discontinuities—Part 1:Bolts, screws and studs for general requirements Iso 8839,Mechanical properties of fasteners—Bolts, screws, studsand nuts made of non-ferrousmetals ISO8992,Fasteners- Generalrequirementsforbolts,screws,studsandnuts ISO 2011 All rights