BS ISO 10619-3:2011 BSI Standards Publication Rubber and plastics hoses and tubing - Measurement of flexibility and stiffness Part 3: Bending tests at high and low temperatures bsi. ..making excellence a habit. BS ISO 10619-3:2011 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO10619-3:2011 The UK participation in its preparation was entrusted to Technical CommitteePRI/66/-/4,Rubberandplasticstubing,hoses and hose assemblies - Methods of test. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. @ BSI 2011 ISBN9780580654237 ICS 23.040.70 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2011. Amendmentsissuedsincepublication Date Text affected BS ISO 10619-3:2011 INTERNATIONAL Iso 10619-3 STANDARD First edition 2011-12-01 Rubber and plastics hoses and tubing Measurement of flexibility and stiffness Part 3: Bending tests at high and low temperatures Tuyaux ettubes en caoutchouc et en plastique-Mesuragede la flexibilite et de la rigidité Partie 3: Essais de courbure a des températures basses et élevées Reference number ISO 10619-3:2011(E) TSO @ISO2011 BS ISO 10619-3:2011 ISO 10619-3:2011(E) COPYRIGHTPROTECTEDDOCUMENT ISO 2011 All rights sreserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 : CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ii @ ISO 2011 - All rights reserved BSISO 10619-3:2011 ISO 10619-3:2011(E) Foreword out throughiSO technical committees. Each memberbody interested in a subjectfor which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with IsO, also take part in the work. isO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2 Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as International Standard requires approval by at least 75 %of the member bodies casting a vote Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO10619-3waspreparedbyTechnicalCommitteeISO/TC45,Rubberandrubberproducts,Subcommittee SC 1, Hoses (rubber and plastics). Iso 10619 consists of the following parts, under the general titleRubberandplasticshoses and tubing- Measurementofflexibilityandstiffness: Part 1: Bending tests at ambienttemperature Part 2:Bending tests at sub-ambient temperatures Part3:Bendingtestsathighandlowtemperatures ed ili BS ISO 10619-3:2011 ISO 10619-3:2011(E) Introduction This method was originally included in IS 1746.THis part of ISO L0619 allows for samples to be tested at sub-ambient temperatures and at elevated temperatures of upto 20o °C. 1) Withdrawn. iv @ ISO 2011 - All rights reserved