金融行业标准网
文库搜索
切换导航
文件分类
频道
文件分类
批量下载
GB 中华人民共和国国家标准 GB/T 19042.4—2005/IEC 61223-3-4:2000 医用成像部门的评价及例行试验 第3-4部分:牙科X射线设备成像 性能验收试验 Evaluation and routine testing in medical imaging departments-Part 3-4 : Acceptance tests-Imaging performance of X-ray equipment (IEC61223-3-4:2000,IDT) 2005-01-27发布 2005-08-01实施 中华人民共和国国家质量监督检验检疫总局 发布 中国国家标准化管理委员会 GB/T19042.4—2005/IEC61223-3-4:2000 目 次 前言 引言 范围和目的 1. 1 适用范围 1. 2 目的 2 规范性引用文件 3 术语 3.1 要求的程度 3.2 术语的使用 3.3 定义的术语 验收试验的通用要求 4. 1 试验过程中应考患的 一般条件 4.2 试验用的文件和数据 4.3 试验条件 4.4 试验的范围 4.5 试验设备包括体模和试验器件 4.6 试验结果的评价 具有口内X射线影像接受器的牙科X射线设备的试验方法 5.1 目测和功能试验 5. 2 *X射线管电压 5.3 *总滤过 5. 4 *X射线管的焦点 5.5 X射线束的限制和校准 5. 6 焦点到皮肤的距离 *辐射输出的重复性 5.8 线对分辨率 5. 9 低对比分辨率 具有口外X射线影像接受器的牙科全景X射线设备试验 6. 1 目测和功能试验 6.2 X射线管电压 6.3 总滤过 6.4 X射线管焦点 6.5 X射线束的限制和校准 6.6 焦点至皮肤距离 6.7 辐射输出的重复性 6.8 线对分辨率 6.9 低对比度分辨率 6.10 带增感屏的X射线胶片暗厘
GB-T 19042.4-2005 医用成像部门的评价及例行试验 第3-4部分 牙科X射线设备成像性能验收试验
文档预览
中文文档
25 页
50 下载
1000 浏览
0 评论
309 收藏
3.0分
赞助2元下载(无需注册)
温馨提示:本文档共25页,可预览 3 页,如浏览全部内容或当前文档出现乱码,可开通会员下载原始文档
下载文档到电脑,方便使用
赞助2元下载
本文档由 人生无常 于
2024-07-06 23:43:25
上传分享
举报
下载
原文档
(22.6 MB)
分享
友情链接
ISO 12614-10 2021 Road vehicles Liquefied natural gas (LNG) fuel system components Part 10 Rigid fuel line in stainless steel.pdf
ISO TR 10982 2013 Road vehicles — Test procedures for evaluating out-of-position vehicle occupant interactions with deploying air bags.pdf
ISO 14903 2017 Refrigerating systems and heat pumps — Qualification of tightness of components and joints.pdf
ISO TR 16250 2013 Road vehicles — Objective rating metrics for dynamic systems.pdf
ISO 80601-2-87 2021 Medical electrical equipment - Part 2-87 Particular requirements for the basic safety and essential performance of high frequency ventilators.pdf
ISO 13774 1998 Rubber and plastics hoses for fuels for internal-combustion engines — Method of test for flammability.pdf
ISO-TS 21623 2017 Workplace exposure Assessment of dermal exposure to nano-objects and their aggregates and agglomerates (NOAA).pdf
ISO 3026 1992 Cinematography — Printed 8 mm Type S image area on 35 mm motion-picture film perforated 8 mm Type S, 2R-4.227 (1664) or 5R-4.234 (1667) — Position and dimensions.pdf
ISO TR 22085-1 2019 Intelligent transport systems (ITS) — Nomadic device service platform for micro-mobility — Part 1 General information and use case definitions.pdf
ISO 3506-1 2020 Fasteners Mechanical properties of corrosion-resistant stainless steel fasteners Part 1 Bolts screws and studs with specified grades and property classes.pdf
GB-T 14536.20-2008 家用和类似用途电自动控制器 水流和气流敏感控制器的特殊要求, 包括机械要求.pdf
GB-T 16511-1996 电气和电子测量设备随机文件.pdf
GB-T 40015-2021 信息技术 系统间远程通信和信息交换 社区节能控制网络控制与管理.pdf
GB-T 23698-2009 三维扫描人体测量方法的一般要求.pdf
GB-T 25160-2010 包装 卡纸板折叠纸盒结构尺寸.pdf
GB 10080-2001 空调用通风机安全要求.pdf
GB-T 21806-2008 化学品 鱼类幼体生长试验.pdf
GB-T 4956-2003 磁性基体上非磁性覆盖层 覆盖层厚度测量 磁性法.pdf
GB-T 2492-2017 固结磨具 交付砂轮允许的不平衡量 测量.pdf
GB-T 11081-2005 白油紫外吸光度测定法.pdf
1
/
3
25
评价文档
赞助2元 点击下载(22.6 MB)
回到顶部
×
微信扫码支付
2
元 自动下载
官方客服微信:siduwenku
支付 完成后 如未跳转 点击这里 下载
站内资源均来自网友分享或网络收集整理,若无意中侵犯到您的权利,敬请联系我们
微信(点击查看客服)
,我们将及时删除相关资源。